# Impact, Fatigue, and Hardness – Lab Report Template Essay

4189408-25613300GENG211 ” Material Science Laboratory Report # 3: Impact of Charpy, Fatigue, & Hardness TestsSpring 2018-2019Submitted to Dr. Mohamad ZbibSection Number Group Number Date of Submission Deadline: Saturday, May 18, 2019 at 11:00 PMName IDPart 1: Charpy Impact TestSummary:In this part, you must write three paragraphs (1/2 page, single spaced) that include:1.1. Purpose of the experiment1.2. Methodology1.3. Main Results1.4. Table 1: Fracture Energy Data for the Tested Materials.± (degrees) І (degrees) Fracture Energy (J) Average Energy (J)All trials A B C D A B C D Brass 101 3 3 3 3 2.

78 2.78 2.78 2.78 Al 64 68 56 75 1.47 1.28 1.75 1.02 Mild Steel 3 2 2 3 2.78 2.78 2.78 2.78 Cupper 54 71 46 46 1.82 1.20 2.07 2.07 1.5. Determine the average fracture energy for each materials, and fill it in the corresponding cell in Table 1.1.6. Discuss the difference in the fracture energy of the four different materials.1.7. Discuss the difference in fracture energy within the same material (for example, the changes in energy for Al).1.8. Table 2: Fracture Energy Data for a Specific Material at Different TemperaturesTemperature (°C) Impact Energy (J)100 89.375 88.650 87.625 85.40 82.9-25 78.9-50 73.1-65 66.0-75 59.3-85 47.9-100 43.3-125 29.3-150 27.1-175 25.01.9. Fracture Energy vs. Temperature CurvePlot the curve1.

Don't use plagiarized sources. Get Your Custom Essay on
Impact, Fatigue, and Hardness – Lab Report Template Essay
From as low as \$9/Page

10. Transition TemperatureDetermine the transition temperature from the plot.1.11. What is the difference between strength and toughness?Part 2: Fatigue Test2.1. Table 3. Fatigue Test DataStress (ksi) Cycles to Failure (x102)56.7 27155.4 40453.4 83652.8 153751.0 263949.5 400048.3 540047.5 135892.2. S-N Plot2.3. Fatigue Limit (Endurance Limit)Part 3: Hardness TestSummary:In this part, you must write three paragraphs (1/2 page, single spaced) that include: Purpose of the experimentThe reason for this examination is to measure the perpetual profundity of the indentation that is applied by a force on the indenter, therefore to look at and think about the hardness of various metals relying upon the profundity of the space. Experimental methodsIn the wake of setting the machine correctly, we raise the specimen to such an extent that it become in contact with the indenter by turning the big screw to such an extent that the center gage becomes vertical and modify the little screw to set the dial to zero. After that we press the switch and start the test. The last position of the dial pointer gives Rockwell hardness number which is straightforwardly identified with the profundity on indentation. At that point we take the recorded values legitimately from the screen. At that point we do a similar technique for the remaining materials. Main resultsAfter we are done doing the experiment, we recorded the values of the trail given by the machine. We calculated the average and we found out that material D has an average of 93.03 which is the highest while material A has an average of 70.54 which is the lowest. This proves that material D is the hardest one and material A is the weakest one. The increasing order of hardness was D > C >B >A which is proved in the table below.Table 4. Hardness ValuesRockwell Hardness (HRC)Trial Average Standard DeviationMaterial 1 2 3 4 5 6 A 70.19 69.75 70.68 71.03 70.80 70.79 70.54 0.47B 84.41 84.08 84.58 79.90 84.25 84.91 83.68 1.88C 86.62 86.95 87.43 87.53 82.34 87.52 86.39 2.02D 91.35 91.91 92.02 91.72 98.89 92.33 93.03 2.883.5. Determine the average and the standard deviation of each sample in the Table 4. Write the values in the corresponding cells.Average =16Trail6=91.35+91.91+92.02+91.72+98.89+92.336=93.03 HRC.Standard Deviation = (T-Tav)^(2)6-1For specimen D: Standard Deviation = 91.35-93.032++(92.33-93.03)^(2)6-1=2.88 HRC.Discuss two factors that explain the differences in the measurements within each sample.Surface impurities: They could be because of a previous indent in the surface of the material that is utilized which could straightforwardly influence the estimations and recorded values.Cleanliness: The surface could have dust on it which is a boundary and could change the estimation results.What other techniques could be used to get much more accurate hardness measurements?The other indentation techniques which give a better result rather than on a macro-scale (HRC) we shall use:Vickers Hardness Test: we are talking about micro-scale.Nano-Indenter: we are talking about Nano-scale.This test is more accurate than the previous ones.3.8. Why some materials are harder than others?Some materials are harder than others because of the presence of the grain boundaries. The case is totally different in metals because of the rolling process and how atoms are aligned. Therefore, the more grain boundaries exist the more hardness we get. Moreover, some metals are mixture like iron, nickel etc… which definitely makes the material more harder.

## How Do I Place an Order With a Paper Writing Service??

Take a few steps to place an order on our site:

• Fill out the form and state the deadline.
• Calculate the price of your assignment order and pay for it with your credit card.
• When the order is placed, we select a suitable expert writer to complete it based on your requirements.
• Stay in contact with the writer and discuss vital details of research.
• Download research paper preview. Satisfied with the research paper outcome? Press “Approve.”

### Feel secure when using our writing service

It's important for every customer to feel safe. Thus, at The Homework Writings, we take care of your security.

Financial security You can safely pay for your order using secure payment systems.
Personal security Any personal information about our customers is private. No other person can get access to it.
Academic security To deliver no-plagiarism samples, we use a specially-designed software to check every finished assignment.
Web security This website is protected from illegal breaks. We constantly update our privacy management.

Get assistance with placing your order. Clarify any questions about our homework writing services. Contact our support team. They are available 24\7.

Still thinking how to find a writer to boost my grades? Place your order on our website and get help with paper writing of your choice. We’ll meet your academic expectations.